• ASAP Fabrication
  2-seater Beam
  1.5" .120 / 1" .095 tube
• TUBE CONNECTOR, 1.50" X 0.120", WELD IN (for removable rear cage)
• 2 Step Powder Coating by Portland Powder Coating

• PRP suspension seats
  (high Back Buckets)
• Dual slide mounts
• Billet adjustable grab handle

FUEL

• GAS TANK, ALUMINUM,W/SUMP AND RETURN,10" X 33"-11 GAL, END FILL   
• VALVE, FUEL SHUT OFF    

• 6 rib 091 bus trans
• Hecker Machine GM to VW adapter
• Stage 2 Kennedy Clutch Pressure plate/TOB
• 8 inch 6 puck disk
• Sway Away Porsche Axle, 19.25" long, 28 tooth
• Sway Away IRS Axle Spacers
• Sway Away 930CV Bolts, 3/8 - 24 thread
• 091 to 930 drive flange
•  EMPI Stub Axle T1 to 930CV
• EMPI Smooth Bushings 1 7/8" ID, PR
• GKN Automotive Porsche 930 CV Joint Bearing
• SKF Bearing Outer
• SKF Bearing Inner
• - Misc. bolts, (2) gasket sets, (2) Axle Castle Nuts, (2) C-Clips, (2) O-Rings, (2) Axle Bolts, (4) CV Boots, Etc.
   

• 1989 GMC 4.3L TBI
• Painless Performance 4.3L TBI wiring harness
• Red top OPTIMA Battery
• HIGH TORQUE STARTER,76-79 091 BUS

Brakes

• CNC Inc. 648L Aluminum Disc Brakes 5 lug off road disc brake kit, long spline
• AN(Army Navy) #3 ss braided Lines
  & 1/8" NPT to #3 AN adapters

REAR SUSPENSION

• Eagle Performance 3x3 tube trailing arms
• EAGLE Spring plate conversion kit
• Type I bolt in Bearing Carriers
• 12" BEARD 2x suspension Straps

SAFETY

• SIMPSON 2x2 Y-harnesses
  with sewn in pads
• T-handle adjustable billet Grab bar

• AXLE BEAM, CHROMOLY, 6 INCH WIDER W/O TOWERS
• POLYURETHANE BUSHING KIT
• THRU RODS, 5" OR 6" WIDER AXLE BEAMS
• COMBO LINK SPINDLE, HEAVY DUTY FOR INT. TIE ROD ENDS 
• FRONT TRAILING ARMS
  4" X 1 3/4" LONGER FOR THRU RODS      
• HD LINK PIN FOR EXTENDED FRONT TRAILING ARMS
• WIDE 5 WHEEL HUBS (washers, studs, and nuts)
• BRONZE BUSHING LINK PIN, FITS above
• TIE ROD SET 6" WIDER BEAM, INT. ENDS
• MOUNT, URETHANE, 2 1/2" SHOCK RESERVOIR TO 1 1/2" TUBING 
• 22" BEARD 2x suspension straps

• Grant 440 Steering Wheel
• OFF-ROAD Rack & Pinion
• Billet steering carrier 7/8" shaft with needle bearings
• U-JOINT FOR RACK AND PINION, 5/8" -36 SPLINE
• CNC hydraulic pedal assembly with throttle
• CNC 2# residual valve
• CNC dual handle cutting brakes 
• T-handle Shifter
• Adjustable Urethane shift coupler
• Slide plate for Pedal Assembly
• MOUNT FOR PEDAL ASSEMBLY

LIGHTS

• SIGNAL SWITCH,UNIVERSAL BUGGY STYLE
• SWITCH, BRAKE LIGHT, 2 PRONG
• BRAKE LINE T ADAPTER, FOR SENDER, RADIUSED FOR 1 1/2" TUBE MOUNT 
• TAILLIGHT,MINI LED,RED(STOP)/AMBER(TURN)2 1/2 X 13/4 X 2
• TAILLIGHT,MINI,RED 2 1/2 X 1 3/4 X 2
• TAILLIGHT,MINI,AMBER 2 1/2 X 1 3/4 X 2
• 6 Inch Chrome offroad lights

WHEELS and TIRES

• Douglas 15x12 wide 5 rear wheels
• Dick Cepek 16.5 paddles
• Douglas 15 x 4.5
  2" backspace wide 5 front wheels
• 165/r15 Nankang front tires
• 15x7 Robby Gordon
  Beadlocker rims

ACCESSORIES

• Canvas top (velcro attached)
• Bolt-on fold down whip holder
• Trunk Wing from Tech 3